1. Reflux Extraction Test Set
Product Code
|
UTAS-0013 |
Reflux Extraction Test Set 1000 g, 220-240 V 50-60 Hz |
|
UTAS-0014 |
Reflux Extractor Jar 1000 g |
|
UTAS-0015 |
Reflux Extractor Condenser 1000 g |
|
UTAS-0016 |
Reflux Extractor Conical Wire Screen 500 g |
|
UTGH-1830 |
Iron Wire Gauze 120x120mm |
|
UTAS-0020 |
Reflux Extraction Test Set 4000 g, 220-240 V 50-60 Hz |
|
UTAS-0021 |
Reflux Extractor Jar 4000 g |
|
UTAS-0022 |
Reflux Extractor Condenser 4000 g |
|
UTAS-0023 |
Reflux Extractor Conical Wire Screen 2000 g |
|
UTAS-0024 |
Filter Paper Ø300mm (50 pcs./pack) for UTAS-0013 |
|
UTAS-0025 |
Filter Paper Ø 400mm (50 pcs./pack) for and UTAS-0020 |
|
UTGH-1835 |
Iron Wire Gauze 160x160mm |
Standards
ASTM D2172
The Reflux Extractor is used for the quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples. The bitumen content is calculated by difference from the weight of extracted aggregates, moisture content and ash from an aliquot part of the extract.
The Reflux Extraction Test Sets are supplied complete with;
- Cylindrical Glass Extractor Jar
- Two Wire Mesh Cones with Interlocking Frames
- Water Condenser with Inlet/Outlet Tubes
- Filter Paper, 50 pcs./pack
- Hot Plate
- Iron Wire Gauze (UTGH-1830 with UTAS-0013, UTGH-1835 with UTAS-0020)
|
Dimensions |
UTAS-0013 |
200x200x800 mm |
|
UTAS-0020 |
330x600x330 mm |
|
|
Weight (approx.) |
UTAS-0013 |
7 kg |
|
UTAS-0020 |
8 kg |
2. Centrifuge Extractor
Product Code
|
UTAS-0030 |
Centrifuge Extractor 1500 g |
|
UTAS-0031 |
Filter Paper 250 mm Outer dia. 45 mm Inner dia. for UTAS-0030 (100 pcs/Pack) |
|
UTAS-0032 |
Rotating Bowl and Cover for UTAS-0030 |
|
UTAS-0035 |
Centrifuge Extractor 3000 g capacity, 220-240 V 50-60 Hz |
|
UTAS-0036 |
Filter Paper 295 mm Outer dia. 45 mm Inner dia. for UTAS-0035(100 pcs / Pack) |
|
UTAS-0037 |
Rotating Bowl and Cover for UTAS-0035 |
|
Models for 220-240V 50-60 Hz, 1 ph. |
UTAS-0030 |
UTAS-0035 |
|
Models for 110-120V 60 Hz, 1 ph. |
UTAS-0030-N |
UTAS-0035-N |
Standards
EN 12697-1 Clause B.1.5; AASHTO T164 A; ASTM D2172 A
The Centrifuges are used for the determination of the bitumen percentage in bituminous mixtures. All models comprise a removable precision-machined rotor bowl housed in a cylindrical aluminum box. The bowl is driven by an electric motor fitted with an AC drive (inverter) with the double function of speed control up to 3600 rpm regardless of the frequency (50 or 60 Hz) and electrical breaking. The centrifuge can be set for the automatic speed ramp up to 3600 rpm and will stop in 10-15 seconds.
The cover is precisely machined and fitted with a solvent resistant gasket to avoid leakages.
The control panel includes: Start/Stop button and speed control knob.
Filter paper UTAS-0031 for UTAS-0030 or Filter paper UTAS-0036 for UTAS-0035 should be ordered seperately
The Centrifuge Extractor is supplied complete with;
- Bowl and Cover
UTAS-0031 UTAS-0032 UTAS-0036 UTAS-0037
|
Dimensions |
370x550x550 mm |
|
Weight (approx.) |
40 kg (for both models) |
|
Power |
370W (for both models) |
3. Asphalt Binder Analyzer (ABA)
Product Code
|
UTAS-0060 |
Asphalt Binder Analyzer (ABA) by the Ignation Method |
|
UTAS-0061 |
Spare Basket and Tray Set |
|
UTAS-0062 |
Cooling Cage |
|
UTAS-0065 |
Metal Stand for UTAS-0060 |
|
Models for 380V, 50 Hz, 3 ph. |
UTAS-0060-C |
Models for 240 V, 60 Hz, 2 ph. |
UTAS-0060-V |
|
Models for 208 V, 60 Hz, 3 ph. |
UTAS-0060-NC |
Models for 220-240V 50-60 Hz, 1 ph |
UTAS-0060 |
Standards
EN 12697-39; AASHTO TP53, T308; ASTM D6307
The UTEST ABA Asphalt Binder Analyzer is used to determine the binder content of hot mix asphalt/bituminous mixtures by the method of loss on ignition. The system combines a sophisticated furnace and weighing system to continuously measure the weight loss of a bituminous mixture during combustion and automatically calculates its binder content at the end of the test.
Supplied complete with 2 specimen baskets with a safety cover, a carrying tray, a fork to catch the tray, and 3m metal exhaust pipe. The Metal Stand (UTAS-0065), the cooling cage (UTAS-0062) and if the tests are to be performed consecutively without waiting for cooling, the Spare Basket and Tray Set (UTAS-0061) shoud be ordered seperately.
UTAS-0061 Spare Basket and Tray Set consists of 2 pcs. basket (one has a safety cover) and a carrying tray.
OVEN AND AFTERBURNER
- High efficiency heating system with afterburner chamber for a total combustion of exhaust fumes to minimize emissions to conform with EU Directives
- Sample size up to 4500 g for more representative test results
- Maximum power rating is 10 kW
HARDWARE
- 16 bit microprocessor with one CPU card controlling test data display, temperature, database and internal functions
- Large permanent memory to store test results
- On board 40 column serial printer
- Weighing system 15000 g capacity, 0.1 g resolution and detecting mass variations of ± 0,1 g
- PID closed loop thermoregulation for both oven and afterburner chamber
- 800 ºC Afterburner 540 ºC oven set temperature according to standard
- TFT touchscreen with 800x480 resolution and 65000 colors
FIRMWARE
- Bidirectional real time communication with the weighing system
- Test setting menu with physical and descriptive sample parameters (initial weight, weight loss percentage, correction factor)
- Calibration menu to check and set the temperature and weight calibration for possible manual control of the test performance
- Test performance menu with simultaneous display of all the test data
- Internal memory for up to 100 tests
SAFETY FEATURES
- Automatic door locking after 150 ºC
- Automatic monitoring of closed door before test start
The UTEST ABA Asphalt Binder Analyzer is supplied complete with;
- Two Specimen Basket with a Safety Cover
- A Carrying Tray
- Carrying Fork
- 3m Metal Exhaust Pipe
|
Dimensions |
670x1140x1230 mm |
|
Weight (approx.) |
135 kg |
|
Power |
10 kW |
4. Solvent Recovery Unit
Product Code
|
UTAS-0091 |
Solvent Recovery Unit 10 lt/h Capacity |
|
Models for 220-240V 50-60 Hz, 1 ph. |
UTAS-0091 |
|
Models for 110-120V 60 Hz, 1 ph. |
UTAS-0091-N |
Non-flammable solvent liquids used for the binder extraction test can be successfully recovered using the UTAS-0091 Solvent Recovery Unit.
The recovery unit consists of two stainless steel chambers, one for the dirty used solvent and the other for the cleaned recovered solvent.
Solvent in the left-hand side chamber is distilled by an electrical heater and then passes through a water cooling system and drops into the second chamber ready for re-use.
A temperature switch automatically stops the heating elements when the recovery process is completed.
The unit is supplied complete with 3 m plastic tubing, tube clamps, sieve insert 0.6 mm opening and one lid.
The Solvent Recovery Unit is supplied complete with;
- Plastic Tubing, 3 m
- Tube Clamps
- Sieve Insert, 0.6 mm
- Lid
|
Dimensions |
360x420x600 mm |
|
Weight (approx.) |
21 kg |
|
Power |
1200 W |
|
Max. Tempature |
150°C |
5. Vacuum Pyknometer (Yale Pycnometer) for Rice Test
Product Code
|
UTAS-0093 |
Vacuum Pyknometer (Yale Pycnometer) for Rice Test 4.3L, Aluminium |
|
UTAS-0094 |
Large Size Heavy Duty Vacuum Pyknometer (Yale Pycnometer) for Rice Test, 10 L |
|
UTG-0310 |
Vibro-Deaerator, Timer Controlled |
|
UTGE-3505 |
Vacuum Pump, 51 lt/min Capacity, 220-240 V 50-60 Hz, 1ph |
|
UTGE-3530 |
Dual Stage Vacuum Pump 128 lt/min Capacity, 220-240 V 50-60 Hz, 1ph |
|
UTGE-3552 |
Vacuum Gauge, Analog, -100 kPa, 1 kPa graduated, dia: Ø 63 mm |
|
UTGE-3570 |
Air Drying Unit/ Water Trap, Vacuum Type |
|
UTGG-2016 |
Filter Flask for Vacuum, 2000 ml |
|
Models for 220-240V 50-60 Hz, 1 ph. |
UTG-0310 |
|
Models for 110-120V 60 Hz, 1 ph. |
UTG-0310-N |
Standards
ASTM D2041; EN 12697-5
The Vacuum Pyknometers (Yale Pyknometer) are used for determining the theoretical maximum specific gravity and density of compacted or non-compacted bituminous paving mixtures (voidless mass).Percent air voids in compacted bituminous mixtures and the amount of bitumen absorbed by the aggregates can also be calculated with the test.
UTAS-0093 consists of a 4,3 liter aluminium container, a transparent vacuum lid a aluminium volumetric lid.
UTAS-0094 consists of a 10 liter transparent plastic container, a transparent plastic vacuum lid and a transparent plastic plate.
To complete the test, vibro-deairator(UTG-0130), vacuum pump, vacuum gauge(UTGE-3552), 2 pcs. filter flask (UTGG-2016) or air drying unit / water trap (UTGE-3570) should be ordered separately, in addition to UTAS-0093 or UTAS-0094.
Vacuum Pumps are supplied with 3m plastic tube (Ø8mm OD, - UTGP-1440)) and an auto-nipple.
UTGE-3552 Vacuum gauge, analog, scale range (-100/0 kPa), accuracy (1.0 % of scale range), 1 kPa graduated, Ø63 mm. Supplied with a valve, 4-way dispenser muffler and. its hanger.
|
Product Code |
External Dimensions |
Weight (approx.) |
|
UTAS-0093 |
210x210x350 cm |
7 kg |
|
UTAS-0094 |
300x300x450 cm |
7 kg |
|
UTG-0310 |
500x500x320 cm |
90 kg |
|
UTGE-3505 |
290x290x220 cm |
7 kg |
|
UTGE-3530 |
340x140x240 cm |
10 kg |
6. Laboratory Mixer 10 L
Product Code
|
UTG-0130 |
Laboratory Mixer 10 L |
|
UTAS-0187 |
Heating Mantle for UTG-0130 |
|
UTG-0131 |
Spare Bowl for UTG-0130 |
|
UTG-0132 |
Spare Whisk for UTG-0130 |
|
Models for 220-240V 50-60 Hz, 1 ph. |
UTG-0130 |
UTAS-0187 |
|
Models for 110-120V 60 Hz, 1 ph. |
UTG-0130-N |
UTAS-0187-N |
Standards
EN 12697-35
The UTG-0130 10 litre capacity Laboratory Mixer is designed for mixing of soil and asphalt samples to be used for mechanical tests such as compaction, indirect tensile, Marshall etc. The mixing head rotates at speeds of 10 to 240 r.p.m. and the whisk from 20 to 480 r.p.m. The user can adjust rotation speed between given values easily by using a control knob fitted to the front panel.
The bituminous mixture must be prepared at the prescribed temperature according to the EN standard. For this reason the mixer can be equipped with thermostatically controlled heater.
The Heating Mantle (Isomantle heater) has a digital thermostatic controller and used for heating the bituminous mixtures in the UTG-0130 up to 150°C. The Isomantle heater is supplied complete with PT100 temperature sensor.
Heating Mantle should be ordered separately.
UTAS-0187
The Laboratory Mixer is supplied complete with;
- Bowl,10 lt Capacity Stainless Steel
- Mixing Whisk
UTG-0132 UTG-0131
|
|
UTG-0130 |
UTAS-0187 |
|
Dimensions |
600x620x700 mm |
310x380x200 mm |
|
Weight (approx.) |
65 kg |
6 kg |
|
Power |
550 W |
600 W |
7. Laboratory Mixer 7.5 L
Product Code
|
UTAS-0195 |
Asphalt Mixer, 7.5 L |
|
UTAS-0196 |
Spare Mixing Bowl, 7.5 L, for UTAS-0195 |
|
UTAS-0197 |
Spare Mixing Whisk, for UTAS-0195 |
|
Models for 220-240V 50-60 Hz, 1 ph. |
UTAS -0195 |
|
Models for 110-120V 60 Hz, 1 ph. |
UTAS 0195-N |
Standards
EN 12697-35
The mixer has a capacity of 7.5 liters and is designed for mixing of asphalt samples to be used for mechanical tests such as compaction, indirect tensile, and Marshall. The mixer does not contain a heater.
The Laboratory Mixer is supplied complete with;
- Bowl, 7,5 lt Capacity, 5,5 kg, Stainless Steel
- Mixing Whisk
UTAS-0196 UTAS-0197
|
Dimensions |
370x570x700 mm |
|
Weight (approx.) |
70 kg |
|
Power |
550 W |
8. Marshall Compaction Mould
Product Code
|
UTAS-0641E |
Marshall Compaction Mould for Impact Compactor with Wooden Pedestal, EN, 101.6 mm |
|
UTAS-0642E |
Base Plate for UTAS-0641E |
|
UTAS-0643 |
Collar for UTAS-0641E and UTAS-0641A |
|
UTAS-0644 |
Mould Body for UTAS-0641E and UTAS-0641A |
|
UTAS-0641A |
Marshall Compaction Mould ASTM 4” |
|
UTAS-0642A |
Base Plate for UTAS-0641A |
|
UTAS-0646A |
Marshall Compaction Mould ASTM 6” |
|
UTAS-0664 |
Marshall Storage Plate for 6 pcs. for 4” (101.6mm) specimens |
Standards
EN 12697-30; ASTM D1559, D6926, D5581; AASHTO T245
The Marshall Compaction Moulds are used to produce the Marshall specimens with automatic or manual compactors. The moulds are manufactured using galvanized steel. UTAS-0664 Marshall Storage Plate is designed to store 6 pcs , 4” diameter Marshall specimens.
UTAS-0641E, UTAS-0641A and UTAS-0646A compaction moulds comprise a base plate, a mould body and a collar.
UTAS-0641E UTAS-0642A
UTAS-0664
|
|
Dimensions |
Weight (approx.) |
|
UTAS-0641E |
Ø120x170 mm |
3,5 kg |
|
UTAS-0641A |
Ø120x170 mm |
3,5 kg |
|
UTAS-0646A |
Ø175x210 mm |
6 kg |
|
UTAS-0664 |
250x500x70 mm |
6 kg |
9. Marshall Manual Compaction Assembly, ASTM
Product Code
|
UTAS-0670 |
Manual Marshall Compaction Assembly, 4”, ASTM |
|
UTAS-0671 |
Marshall Compaction Hammer, 4” ASTM |
|
UTAS-0672 |
Wooden Compation Pedestal, ASTM, for UTAS-0670 |
|
UTAS-0674 |
Marshall Compaction Hammer BS |
|
UTAS-0676 |
Manual Marshall Compaction Assembly, 6”, ASTM |
|
UTAS-0677 |
Marshall Compaction Hammer, 6”ASTM, for UTAS-0676 |
|
UTAS-0678 |
Wooden Compaction Pedestal, 6”, ASTM, for UTAS-0676 |
|
UTAS-0667 |
Marshall Steel Block, Ø102 mm dia. and 50 mm height, |
|
UTAS-0668 |
Marshall Steel Block, Ø154mm dia. and 50 mm height, |
Standards
ASTM D6926, D5581; AASTHO T245 (only for UTAS-0071); BS-598
The UTAS-0670 and UTAS-0676 Marshall Manual Assemblies are used to prepare Marshall specimens manually.
The Compaction Assemblies consist of a Marshall Compaction Hammer and a Wooden Compaction Pedestal. The Pedestals are supplied complete with a steel plate, a mould holder and a hammer guide.
UTAS-0667 and UTAS-0668 Marshall Steel Blocks are used for initial heating of the foot of compaction hammer should be ordered separately.
|
|
Dimensions |
Weight (approx.) |
|
UTAS-0670 |
380x380x1570 mm |
45 kg |
|
UTAS-0671 |
100x100x108 mm |
8 kg |
|
UTAS-0672 |
350 x400x1600 mm |
42 kg |
|
UTAS-0674 |
150x150x150 mm |
8 kg |
|
UTAS-0676 |
400x380x1510 mm |
60 kg |
|
UTAS-0677 |
400x380x1510 mm |
60 kg |
|
UTAS-0667 |
150x150x100 mm |
4 kg |
|
UTAS-0668 |
200x200x100 mm |
8 kg |
10. Automatic Marshall Impact Compactor, EN
Product Code
|
UTAS-0682E |
Automatic Marshall Impact Compactor with Wooden Pedestal, EN |
|
UTAS-0683E |
Automatic Marshall Impact Compactor with Wooden Pedestal and Soundproof Safety Cabinet |
|
UTAS-0667 |
Marshall Steel Block, Ø102 and 50 mm height |
|
UTAS-0641E |
Marshall Compaction Mould for Impact Compactor with Wooden Pedestal, EN, 101.6 mm |
|
Models for 220-240V 50 Hz, 1 ph. |
UTC-0682E-T |
UTC-0683E-T |
|
Models for 110-120V 60 Hz, 1 ph. |
UTC-0682E-N |
UTC-0683E-N |
|
Models for 220-240V 60 Hz, 1 ph. |
UTC-0682E-K |
UTC-0683E-K |
Standards
EN 12697-30, 12697-10, 12697-12
The UTAS-0682E and 0683E Automatic Marshall Compactor with wooden pedestal provides a uniform and even degree of compaction. The unit incorporates a compaction pedestal, comprising a laminated hardwood block secured to a concrete block by a 300 mm square x 25 mm thick steel plate.
The conveniently positioned control panel comprises of start/stop button, emergency stop button and a direct reading counter used to set the required number of blows.The apparatus stops automatically after the preset number of blows.
The compactors are equipped with a hand operated mould fixing mechanism which locks the mould in place during compaction and reduces vibration of the mould.
The standard model can be supplied with a safety/noise reduction cabinet. The cabinet is lined internally with soundproofing material to reduce sound level conforming to CE directives.
Particular attention has been paid to operator safety by the inclusion of various in-built safety features.
UTAS-0667 Marshall Steel Block which can be used for Initial heating of the foot of compaction hammer and Marshall moulds should be ordered separately.
Technical Specifications
|
Blows Frequency |
50 blows in 55 s to 60 s |
|
Free fall height of the sliding mass |
457±3 mm |
|
Total weight (Guide rod + Foot assembly+ Sliding mass) |
7850 ± 50 g |
|
Concrete Base Dimension |
450x450x200 mm |
|
Laminated Hardwork Block Dimensions |
200x200x450 mm |
|
Laminated Hardwork Block Density |
0,67 Mg/m3 to 0,78 Mg/m3 |
|
Product Code |
UTAS-0682E |
UTAS-0683E |
|
Dimensions |
520x520x1760 mm |
770x870x1970 mm |
|
Weight (approx.) 225 kg |
235 kg |
362 kg |
|
Power |
370 W |
370 W |
11. Automatic Marshall Impact Compactor for 4” Speciments, ASTM
Product Code
|
UTAS-0782A |
Automatic Marshall Compactor with Stationary Base for 4” dia. Specimens, ASTM |
|
UTAS-0783A |
Automatic Marshall Compactor with Stationary Base for 4” dia. Specimens with Soundproof Safety Cabinet, ASTM |
|
UTAS-0667 |
Marshall Steel Block, Ø102 and 50 mm height |
|
UTAS-0641A |
Marshall Compaction Mould ASTM 4” |
|
Models for 220-240V 50 Hz, 1 ph. |
UTC-0782A-T |
UTC-0783A-T |
|
Models for 110-120V 60 Hz, 1 ph. |
UTC-0782S-N |
UTC-0783A-N |
|
Models for 220-240V 60 Hz, 1 ph. |
UTC-0782A-K |
UTC-0783A-K |
Standards
ASTM D 1559 , ASTM D 6926-16; AASHTO T245
Automatic Marshall Compactor is designed to provide a stable and rigid mechanism to be used for preparation of bituminous specimens for Marshall Stability tests.
UTAS-0782A Compactor for compaction of 4” dia. specimens features a heavy-duty design, which stands up well to the constant jarring caused by the compaction process. The compactors are equipped with a hand operated mould fixing mechanism which locks the mould in place during compaction and reduces vibration of the mould
The conveniently positioned control panel comprises of start/stop button, emergency stop button and a direct reading counter used to set the required number of blows. The operator can keep track of the number of blows on an LCD display.
The apparatus stops automatically after the preset number of blows.
The standard models can be supplied with a safety/noise reduction cabinet. The cabinet is lined internally with soundproofing material to reduce sound level conforming to CE directives
UTAS-0667 Marshall Steel Blocks which can be used for initial heating of the foot of compaction hammer and Marshall moulds should be ordered separately.
Technical Specifications
|
Drop Numbers |
55 ± 5 blow/min |
|
Sliding Weight |
4536 ± 9 gr |
|
Falling Height |
457,2±1,5 mm |
|
Tamping Face Dia. |
98,5 mm |
|
|
UTAS-0782A |
UTAS-0783A |
|
Dimension |
400x440x1550 mm |
550x550x1650 mm |
|
Weight (approx.) |
110 kg |
250 kg |
12. Automatic Marshall Impact Compactor with Stationary Base for 4” and 6” Speciments, ASTM
Product Code
|
UTAS-0786A |
Automatic Marshall Compactor with Stationary Base for 4” and 6” dia Specimens, ASTM |
|
UTAS-0787A |
Automatic Marshall Compactor with Stationary Base for 4” and 6” dia. Specimens with Soundproof Safety Cabinet, ASTM |
|
UTAS-0668 |
Marshall Steel Block, Ø154 and 50 mm height |
|
UTAS-0789A |
Ø6” Hammer for UTAS-0786A and UTAS-0787A |
|
UTAS-0641A |
Marshall Compaction Mould ASTM 4” |
|
UTAS-0646A |
Marshall Compaction Mould ASTM 6” |
|
Models for 220-240V 50 Hz, 1 ph. |
UTC-0786A-T |
UTC-0787A-T |
|
Models for 110-120V 60 Hz, 1 ph. |
UTC-0786A-N |
UTC-0787A-N |
|
Models for 220-240V 60 Hz, 1 ph. |
UTC-0786A-K |
UTC-0787A-K |
Standards
ASTM D 1559 , ASTM D 6926-16, D5581; AASHTO T245
UTAS-0786A and UTAS-0787A Automatic Marshall Compactors are designed for the preparation of 4” and 6” bituminous specimens with the same device for Marshall Stability tests
The compactors have a heavy-duty design that withstands the continuous shaking caused by the compaction process and they are equipped with a hand operated mould fixing mechanism which locks the mould in place during compaction and reduces vibration of the moulds.
UTAS-0786A and UTAS-0787A Automatic Marshall Compactors are supplied complete 4” hammer. These compactors can easily be altered later to accommodate the 6” size by purchasing 6” hammer and molds. 6” hammer and the moulds (4” or/and 6”) should be ordered seperately.
The number of blows entered in the control panel by the user is applied automatically. By selecting the 55 blow, these compactors apply a speed of 55±5 compaction blows per minute to a 4” and 6” specimens.
The conveniently positioned control panel comprises of start/stop button, emergency stop button and a direct reading counter used to set the required number of blows. The operator can keep track of the number of blows on an LCD display.
The apparatus stops automatically after the preset number of blows.
The standard models can be supplied with a safety/noise reduction cabinet. The cabinet is lined internally with soundproofing material to reduce sound level conforming to CE directivesç
UTAS-0668 Marshall Steel Blocks which can be used for initial heating of the foot of compaction hammer and Marshall moulds should be ordered separately.
Technical Specifications
|
Mould Dia. |
Sliding Weight |
Falling Height |
|
4" |
4536 ± 9 gr 10 ± 0.02-lb |
457,2 ± 1,5 mm 18 ± 0.06 in |
|
6" |
10210 ± 10 gr 22.50 ± 0.02 lb |
457,2 ± 2,5 mm 18.0 ± 0.1 in |
|
Product Code |
UTAS-0786A |
UTAS-0787A |
|
Dimension |
377x485x1920 mm (14,84”x19,1”x75,6”) |
750x750x1975 mm (29,53”x29,53”x77,76”) |
|
Weight (approx.) |
180 kg (397 lb) |
320 kg (706 lb) |
13. Marshall / CBR / Proctor Specimen Extruder
Product Code
|
UTGE-0080 |
Marshall-CBR-Proctor Specimen Extruder, 30 kN Capacity |
Standards
EN 12697-30, 13286-2, 13286-47; AASTHO T245, T134, T180,T193;
ASTM D1559, D698, D1557, D1883; BS 598-107, 1377-4, 1924-2
The specimen extruder is designed to easily extrude specimens from Marshall, CBR, standard and modified Proctor Moulds. The capacity of the extruder is 30 kN. Supplied complete with a manual hydraulic jack and 2 pcs. adaptor to extrude specimens from 100mm (4“), 150 mm (6”) inner diameter marshall, CBR, standard and modified proctor moulds.
|
Ram Travel |
130 mm |
|
Screw Travel |
90 mm |
|
Dimensions |
280x280x510 mm |
|
Weight (approx.) |
28 kg |
14. Duriez Compression Test Sets
Product Code
|
UTAS-0490 |
Duriez Compression Test Set, 80 mm dia. |
|
UTAS-0495 |
Duriez Grooved Piston Set, for UTAS-0490 |
|
UTAS-0496 |
Duriez Non-Grooved Piston Set, for UTAS-0490 |
|
UTAS-0503 |
Duriez Compression Test Set, 120 mm dia. |
|
UTAS-0505 |
Duriez Grooved Piston Set, for UTAS-0503 |
|
UTAS-0506 |
Duriez Non-Grooved Piston Set, for UTAS-0503 |
Standards
NF P98-251-1 and 4; EN 12697-12 Method B
The test sets are used to determine the physical and mechanical properties of bituminous mixtures, especially for the water sensitivity of bituminous specimens. One set for preparing 80 mm. specimens, the second set for preparing 120mm. specimens according to the maximum aggregate upper sieve size. All parts are made from steel protected against corrosion.
The compression test has to be performed with an electromechanical universal test machine such as UTM-8300.SMD2 model machine (300 kN Electromechanical Universal Test Machine. UTM-8300 can also be used for compaction transaction acc. to EN 12697-12 (Method B) for preparation of test specimens.
Grooved or Non-Grooved piston set includes upper and lower pistons.
Grooved piston set for cold mixes and Non-Grooved piston set for hot mixes should be ordered seperately.
Duriez compression test sets are supplied complete with;
- Mould
- Container
- Extraction Piston
- 2 pcs Half Spacers
15. Vibratory Hammer for Compaction of Bituminous Mixtures and Soil
Product Code
|
UTS-0681-T |
Vibratory Hammer for Compaction of Bituminous Mixtures and Soil, 220-240V, 50 Hz, 1ph. |
|
UTS-0682 |
Steel Tamper, Ø146 mm |
|
UTAS-0885 |
P.R.D. Split Mould and Base Plate |
Standards
EN 12697-32, 12697-9, 12697-10, 13286-4; BS 1377-4
The UTS-0681 Vibratory compaction apparatus are used for preparing the test specimens of bituminous mixtures and soils.
P.R.D. (Percentage Refusal Density) Split Mould is split verticially on one side, attached to the base plate with clamp. Plated against corrosion.
UTAS-0885 The split mould and base plate should be ordered separately.
UTS-0682 the steel tamper which includes a tamping foot and a shank (UTS-0684) should be ordered separately when ordering the vibratory hammer.
|
Dimensions |
350x550x1300 mm |
|
Weight (approx.) (UTS-0681-T) |
105 kg |
|
Impact Rate |
1500-3000/min |
|
Power |
1150W |
16. Marshall Stability Test Machine with Proving Ring
Product Code
|
UTAS-1052 |
Marshall Stability Test Machine with Proving Ring, 50 kN |
|
UTAS-1057 |
Breaking Head (Stability Mould) for Ø4” specimen |
|
UTAS-1058 |
Breaking Head (Stability Mould) for Ø6” specimen |
|
UTAS-1063 |
Indirect Tensile (IDT) Strength/TSRTest Jig / Lottman Breaking Heads with Ø100mm Steel Loading Strips.EN, ASTM, AASHTO EN, ASTM, AASHTO |
|
UTAS-1064 |
Pair of Loading Strips for Ø150 mm Bituminous Specimens. EN, ASTM, AASHTO. For UTAS-1063E and UTAS-1066 |
|
UTAS-1065E |
Pair of Loading Strips for Ø160 mm Bituminous Specimens. EN. For UTAS-1063 |
|
UTAS-1066 |
Indirect Tensile (IDT) Strength / TSR Test jig / Lottman Breaking Heads with Ø4" loading strips. EN, ASTM, AASHTO. |
|
UTAS-1067A |
Pair of Loading strips for Ø6" bituminous specimens.ASTM, AASHTO. For UTAS- 1066 and UTAS-1063 |
|
UTAS-1086 |
Marshall Penetration Piston for StabilityTest, for UTAS-1052 |
|
Models for 220-240V 50-60 Hz, 1 ph. |
UTC-1052 |
|
Models for 110-120V 60 Hz, 1 ph. |
UTC-1052-N |
Standards
EN 12697-34, 12697-23, 12697-12 (Method A); ASTM D1559, D5581, D 6927, D 6931; AASHTO T245
The UTAS-1052 50 kN capacity Marshall Stability Test Machine with Proving Ring is used to determine the maximum load and flow values of bituminous mixtures.
The UTAS-1052 comprises a robust and compact two column frame with adjustable upper cross beam.
The unit is a bench mounted compression frame with motor and worm gear housed within the base unit.
The mechanical jack raises the lower platen at a constant speed of 50.8 mm/min as required in the relevant standard. For safety, the up and down travel of the lower platen movement is limited by limit switches.
Rapid adjustment of the platen is also provided using the control buttons on the front panel of the machine.
The measuring system consists of a 50 kN capacity load ring, digital flow meter (dial gauge) fitted to the breaking head. The UTAS-1052 Marshall Stability Machine is also suitable for testing 6” dia. specimens (152.4 mm) conforming to ASTM D5581.
The machine can be hand operated by a lateral hand wheel for calibration purposes; the hand wheel is supplied complete with the machine.
UTAS-1059 Holder for Digital Dial Gauge(UTGM-0148) is used for connecting to UTAS-1057, UTAS-1058 and UTAS-1063.
UTAS-1063 supplied with a pair of Ø100mm steel loading strip.Loading strips for Ø150 mm and/or Ø160mm and/or Ø4” and/or Ø6” specimens should be ordered separately.
UTAS-1066 supplied with a pair of Ø4” steel loading strip.Loading strips for Ø6” and/or Ø100mm and/or Ø150mm specimens should be ordered separately.
Breaking head/s and/or indirect tensile strength test jig/s should be ordered separately.
The UTAS-1052 Marshall Stability Test Machine is supplied complete with;
- Load Ring, 50 kN
- Penetration Piston for Marshall Stability Test (UTAS-1086)
- Digital Dial Gauge 25x0.01 mm (UTGM-0148) with Holder (UTAS-1059)
- Hand Wheel for Manual Control
|
Dimensions |
470x600x1180 mm |
|
Weight (approx.) |
102 kg |
|
Power |
1100 W |
17. Automatic Marshall Stability Test Machine
Product Code
|
UTAS-1056.ACPR |
Automatic Marshall Stability Test Machine with U-Touch PRO Control Unit, 50 kN / 11000 lbf capacity |
|
UTAS-1057 |
Breaking Head (Stability Mould) for Ø4” Specimen |
|
UTAS-1058 |
Breaking Head (Stability Mould) for Ø6” Specimen |
|
UTAS-1063 |
Indirect Tensile (IDT)Strenght /TSR Test Jig / Lottman Breaking Heads with Ø100mm loading strips.EN, ASTM, AASHTO |
|
UTAS-1064 |
Pair of Loading Strips for Ø150 mm Bituminous Specimens. EN, ASTM for UTAS-1063 and UTAS-1066 |
|
UTAS-1065E |
Pair of Loading Strips for Ø160 mm Bituminous Specimens. EN, for UTAS-1063 |
|
UTAS-1066 |
Indirect Tensile (IDT)Strenght /TSR Test Jig / Lottman Breaking Heads with Ø4” loading strips. EN, ASTM, AASHTO |
|
UTAS-1067A |
Pair of Loading Strips for Ø6” Bituminous Specimens. ASTM, AASHTO for UTAS-1063 and UTAS-1066 |
|
UTM-1088 |
Marshall Penetration Piston for Stability Test, for UTAS-1056 |
|
Models for 220-240V 50-60 Hz, 1 ph. |
UTC-1056.ACPR |
|
Models for 110-120V 60 Hz, 1 ph. |
UTC-1056.ACPR-N |
Standards
EN 12697-34, 12697-23, 12967-12 (Method A) ASTM D1559, D5581, D6927; D6931; AASHTO T245, T283, EN 12697-44; NF P98-251-2
The UTAS-1056.ACPR 50 kN capacity Automatic Marshall Stability Test Machine with U-Touch PRO Control Unit is designed to determine the maximum load and flow values of bituminous mixtures. With suitable accessories UTAS-1056.ACPR can also perform indirect tensile strength test of bituminous specimens.
The machine comprises of a robust, compact two column bench type compression frame with adjustable upper cross beam. Motor, worm gear system and U-Touch PRO Control Unit are housed within the base unit.For safety, up and down travel of the lower platen is limited by limit switches mounted on the gear system. Rapid adjustment of the platen can be done by using the up and down buttons located on the front panel. The machine can be hand operated by a lateral hand wheel for calibration purposes.
Breaking head/s, indirect tensile strength test jig/s and computer should be ordered separately.
UTAS-1063 supplied with a pair of Ø100mm steel loading strip.Loading strips for Ø150 mm and/or Ø160mm and/or Ø4” and/or Ø6” specimens should be ordered separately.
UTAS-1066 supplied with a pair of Ø4” steel loading strip.Loading strips for Ø6” and/or Ø100mm and/or Ø150mm specimens should be ordered separately.
The Automatic Marshall Stability Test Machine is supplied complete with;
- Load Cell, 50 kN
- Penetration Piston for Marshall Stability Test (UTM-1088)
- Linear Potentiometric Displacement Transducer 25 x 0.001 mm (UTGM-0062) with holder (UTAS-1060)
- Utest Software
- Ethernet cable for connecton PC
- Hand Wheel for Manual Control
MAIN FEATURES
- 50 kN capacity
- Stand alone fully automatic test execution
- For marshall, indirect tensile tests.
- Flow and stability values are automatically calculated and saved.
- Touchscreen graphic diplay 800x480 pixel, user-friendly menu consisting of icons, figures and diagrams.
- High resolution: 32 bits
- Large storing capacity on internal memory and data export function to usb stick drive
- Ethernet port for connection to PC
- Language and unit system selection
U-Touch PRO Control Unit
U-Touch PRO Control and Data Acquisition Unit is designed to control and process data from the loadcell and displacement transducers fitted on Marshall Stability test machine. UTAS-1056.ACPR can perform marshall, indirect tensile tests according to EN,ASTM/AASHTO standards listed above.
The Unit can perform tests stand-alone fully, automatic without the need of a PC or USOFT-1056 software. Software can be used to get additional advanges described in the section below.
U-Touch PRO incorporates a user-friendly interface that shows all existing menu options as buttons and tabs. Users can activate or deactivate certain functions easily and input test data by using touch keyboard. Parameters such as test information, user information, sample information and test parameters can be modified and saved for later use by operators.
Control Unit offers many additional unique features. Utouch Pro enables the users to display current memory usage and test results with its advanced data and memory management interface. U-Touch PRO can export, copy, or delete the test data saved in its internal memory. Results and additional information for previous tests can be recalled using U-Touch PRO. Test reports can be instantly printed using an (optional) thermal printer. U-Touch Pro TFT can simultaneously display machine status, test values, warnings during operation and test graphs in real time.
PLEASE see the pages of “General Properties of U-Touch PRO Control Units” for details of the properties of software and hardware of the Unit.
USOFT-1056 UTEST Software for UTAS-1056.ACPR
USOFT-1056 Marshall Stability Test Software is developed for Marshall stability tests in accordance with EN 12697-34, ASTM D 1559, D5581, D 6927, AASHTO T 245, NF P98-0251-2 indirect tensile tests in accordance with EN 12697-23 EN 12697-12(method A), ASTM 6931, AASHTO T283.
The software includes control of machine, acquisition of load and displacement data, saving them and generating reports. The software accepts specimen diameter and height as an input parameter. It automatically calculates correction factor coming from the standards with respect to specimen thickness. The stability value is calculated regarding this factor.
The software continuously updates load and displacement until the end of test. When the test is completed, the sharpest slope of the graph is calculated. The sharpest slope is shifted 1.5 mm to the right side of the graph and the intersection between 2nd slope and original test data is recorded as the stability value for the test. The horizontal distance between the intersection of first slope and X axis and intersection of test data with 2nd slope is recorded as “flow” value.
The point that this line crosses displacement axis is commented as an offset. This offset is subtracted from the displacement value at peak point and called as flow.
The report includes all results for 9 samples. The user can see 9 of the results on the same screen for easy comparision. The software supports SI, Imperial and kgf unit system.
See the pages of “General Properties of Utest USOFT Softwares” for detailed properties of the software.
|
Capacity |
50 kN |
|
Dimensions |
470x600x1180 mm |
|
Weight (approx.) |
102 kg |
|
Power |
1100 W |
18. Core Drilling Machine
UTAS-2101_Core_Drilling_Machine+2.pdf
Product Code
|
UTAS–2101 |
Core Drilling Machine |
|
UTGD–0330 |
Coring Bit for Asphalt 50 mm dia. x 400 mm length |
|
UTGD–0330-S |
Coring Bit for Asphalt 50 mm dia. x 320 mm length |
|
UTGD–0332 |
Coring Bit for Asphalt 75 mm dia. x 400 mm length |
|
UTGD–0332-S |
Coring Bit for Asphalt 75 mm dia. x 320 mm length |
|
UTGD–0334 |
Coring Bit for Asphalt 100 mm dia. x 400 mm length |
|
UTGD–0334-S |
Coring Bit for Asphalt 100 mm dia. x 320 mm length |
|
UTGD–0336 |
Coring Bit for Asphalt 150 mm dia. x 400 mm length |
|
UTGD–0336-S |
Coring Bit for Asphalt 150 mm dia. x 320 mm length |
Standards
EN 12697-27, ASTM D 5361
Machine is designed to cut cores up to 150 mm diameter from concrete, asphalt and similar hard construction materials.
The machine comprises a vertical support column which carries the drill head/motor assembly. The motor assembly comprises a 6.5 Hp petrol engine.
A ball screw mechanism enables close control of the drilling pressure and rapid return when drilling is completed.
A water spraying assembly is mounted on the machine.
The complete assembly is supplied on a rigid wheel mounted metal base frame with leveling and fixing facility during the operation.
Coring Bits should be ordered separately.
UTGD–0336 UTGD–0334 UTGD–0332 UTGD–0330
|
Dimensions |
500x670x1050 mm |
|
Weight (approx.) |
90 kg |
|
Power |
6.5 Hp |
19. Core Drilling Machine on Trailer
Product Code
|
UTAS–2105 |
Core Drilling Machine on Trailer |
|
UTGD–0330 |
Coring Bit for Asphalt 50 mm dia. x 400 mm length |
|
UTGD–0330-S |
Coring Bit for Asphalt 50 mm dia. x 320 mm length |
|
UTGD–0332 |
Coring Bit for Asphalt 75 mm dia. x 400 mm length |
|
UTGD–0332-S |
Coring Bit for Asphalt 75 mm dia. x 320 mm length |
|
UTGD–0334 |
Coring Bit for Asphalt 100 mm dia. x 400 mm length |
|
UTGD–0334-S |
Coring Bit for Asphalt 100 mm dia. x 320 mm length |
|
UTGD–0336 |
Coring Bit for Asphalt 150 mm dia. x 400 mm length |
|
UTGD–0336-S |
Coring Bit for Asphalt 150 mm dia. x 320 mm length |
Standards
EN 12697-27, ASTM D 5361
Portable UTAS-2105Core Drilling Machine is designed to cut cores up to 150 mm diameter from concrete, asphalt and similar hard construction materials.
The machine comprises a vertical support column which carries the drill head/ motor assembly. The motor assembly comprises a 6.5 hp petrol engine.
A ball screw mechanism enables close control of the drilling pressure and rapid return when drilling is completed. A water spraying assembly is mounted on the machine.
The drilling machine is installed in a trailer for fast and precise sampling on-site. 100 litre water tank provides continuous lubrication during drilling to save time.
The two-wheeler taut liner trailer is fully equipped with brake lamps/hazard lashers/retro reflectors conforming to road traffic regulations.
The trailer is designed with a space to be used for storing the core samples. The two fixing legs are robustly designed for improved stabilization.
Coring Bits should be ordered separately.
UTGD–0336 UTGD–0334 UTGD–0332 UTGD–0330
|
Dimensions |
1520x2050x2050 mm |
|
Weight (approx.) |
300 kg |
|
Power |
6.5 Hp |
20. Vialit Plate (Adhesion Test) Apparatus
Product Code
|
UTAS-2112 |
Vialit Plate (Adhesion Test) Apparatus |
|
UTAS-2113 |
Steel Ball, 512gr, for UTAS-0112 |
|
UTAS-2114 |
Mechanical Aggregate Deployment for UTAS-0112, 100 chippings |
Standards
EN 12272-3; NF P98-274-1
The UTAS-0212 Vialit Plate Apparatus is used to assess the adhesion property of aggregates to bitumen.
Supplied complete with a metal basement with three vertical pointed rods to hold the flat steel plate, 50 cm. high vertical rod with a slot at the upper end for the steel ball to drop, a 512 g steel ball, 6 metal test plates and a hand operated rubber wheel roller. The mechanical aggregate deployment should be ordered seperately.
The test plate, coated by bitumen on one face and spread with the aggregate chippings in a standard way is rolled using the roller and then placed on the three-point support base.
The steel ball drops three times from the slot, and the chippings that become loose after the three impacts are counted and checked.
UTAS-2114
The Vialit Plate (Adhesion Test) Apparatus is supplied complete with;
- Flat Steel Plates, 6 pcs.
- Steel Ball, 512 g
- Rubber Wheel Roller, hand operated
|
Dimensions |
550x1650x650 mm |
|
Weight (approx.) |
40 kg |
21. Travelling Beam Device
Product Code
|
UTAS–2125 |
Travelling Beam Device |
The UTAS-2125 Travelling Beam Device is used to check for any irregularities in both concrete and bituminous road surfaces.
Deviation of the surface from a straight-line is shown on a scale calibrated in increments of 2 mm in the 0-10 mm range and 5 mm increments in the 10-25 mm range. It comprises a manual dye marker which is used to mark irregular surface sections when found.
|
Dimensions |
720x2900x500 mm (packed) |
|
Weight (approx.) |
45 kg |
22. MOT Straightedge
Product Code
|
UTAS-2127 |
MOT Straightedge, EN |
|
UTAS-2128 |
Wooden Carrying Case, for UTAS-2127 |
Standards
EN 13036-7
The straightedge is used for measuring single irregularities attributable to quality defects in new surface course(s) of roads, airfields and other trafficked surfaces as well as in-service surfaces.
UTAS-2127 is supplied with two steel wedges.
Wooden carrying case should be ordered separately.
|
Dimensions |
200x3100x150 mm (for case) |
|
Weight (approx.) |
40 kg (with case) |
23. Automatic Asphalt Indentation Penetrometer
Product Code
|
UTAS-2130 |
Automatic Asphalt Indentation Penetrometer, EN |
|
UTAS-2134 |
Spare Indentor Pins (100mm2 and 500 mm2) for UTAS-2130 |
|
UTAS-2135 |
Adjustable mould for the test cube (69mm) for UTAS-2130 |
|
UTAS-2136 |
Metal Intermediate Plate for UTAS-2130 |
|
UTAS-2137 |
Calibration Block for UTAS-2130 |
|
UTAS-2138 |
The appartus for preparing the test cubes for UTAS-2130 |
|
UTCM-0926 |
Cube Mould 70.7 mm, BS, steel, for UTCM-0930 and UTAS-2130 |
|
Models for 220-240V 50-60 Hz, 1 ph. |
UTC-2130 |
|
Models for 110-120V 60 Hz, 1 ph. |
UTC-2130-N |
Standards
TS EN 12697-20
UTAS-2130 Automatic Indentation Penetrometer determines the resistance of an asphalt cube and cylindrical specimens to indentation when force is applied to them using a cylindirical pin in a defined period. Maximum nominal size of the aggregates should be less or equal to 16 mm.
UTAS-2130 can apply a 25 N prelaminary force and than 525 N total force without touching the test weights with electromechanical method acc. to TS EN 12697-20.
UTAS-2130 consists of a four-columns frame combined with an assebly for force application and a stainless steel 25L water bath with drain facility, a digital control unit with immersion type heater-agitator, 50 x 0.01 mm displacement transducer with holder, calibration block, interchangeable indentor pin with 100 mm2 and 500 mm2, an adjustable mould 69mm, a metal intermediate plate and a free software.
Cube mould and the appartus for preparing the test cubes should be ordered seperately.
Key Features
- Stainless steel
- Temperature control
- Digital indicator
- Ethernet connection
Software
UTAS-2130 is supplied with software developed by Utest that allows automatic capture to PC of test data. Software is capable of showing the test data in real time, storing the results and real time temperature monitoring.
Technical Specification
|
Preliminary Force |
(25 ± 1) N |
|
Total Test Force |
(525 ± 1) N |
|
100 mm2 Diameter Indentor Pin |
(11.3 ± 0,1)mm |
|
500 mm2 Diameter Indentor Pin |
(25.2 ± 0,1) mm |
|
Deformation of Apparatus Upon Application and Removal of Forces |
<0.01 mm |
|
Water Tank Capacity |
25 litres |
|
Water Temperature Range |
Ambient to the test temperatures |
|
Water Temperature Stability |
Accuracy of ± 1 °C. |
|
Digital Indicator Resolution |
0.01 mm |
|
Dimensions |
590x1030x480 cm |
|
Weight (approx.) |
196 kg |
24. Non-Nuclear Asphalt Density Gauge
Product Code
|
UTAS–2160 |
Non-Nuclear Asphalt Density Gauge |
Standards
ASTM D7113; AASTHO T 243-12
Non-Nuclear Asphalt Density Gauge is used for determination of density of asphalt specimens with non nuclear method. UTAS-2160 is equipped with a touch screen and user friendly graphical menu interface, running Microsoft Windows silently in the backround for flawless operation, easy software are upgrades and enchanced user support.
The instrument general specifications are;
- Full colour graphics driven interface, 480 x 640 VGA touch screen display with LED backlight for easy visibility.
- Displays GPS status, available battery voltage, low battery and date/time,
- Rugged case design made from aluminum, powder-coated gloss black with orange reflective vinyl graphics increasing driver awareness to road workers at night
- Data Management Feature, quickly access, can be downloaded and deleted project data,
- Required files can be downloaded to UTS-1280 via. USB,
- Fast, reliable, accurate, and repeatable in real time, User Friendly and cost effective.
- The most impoftant point is; Non-Nucleer means no Badges or licences and no storage or transport concerns.
OPERATIONAL FEATURES
- Display: Full color graphics driven user interface, 480x640 VGA touch screen display with LED backlight for easy visibility in daylight or dark environments.
- Status Bar: Displays GPS status, Data Save status, battery voltage, low battery, date and time
- Project Details: Stores up to 20 projects with details,
- Mix Details: Stores up to 20 mixes, details include (MTD, Mix Name, Stone Size, Depth, Offset, Operator Name)
- Data Logging: When enabled, stores all measurements taken in single or average modes, (Status Bar Icon)
- Reports: Easily download data to be imported into Excel
- GPS Control: When activated will display latitude and longitude positions, number of satellites the gauge is connected to as well as the UTC date and time, also available in UTM format. GPS information will store with each measurement when Data Save and GPS feature is enabled, (Status Bar Icon)
- Update Software: One touch upload of new software usinga USB memory stick
- Data Management: Quickly access, download or delete your project data
- Set Time & Date: Quick time and date setup, MM/DD/YY and DD/MM/YY formats
- Units: Interchangeable settings for Density (kq/rn3, Ib/ft3), Temp (°C,°F), Depth (in, mm) and Stone Size (in, mm)
- Standardization: While gauge is still in the case, a quick one touch measurement will ensure the gauge is still in proper working mode
- Calculator: Built in four function calculator
- Enhanced Customer Support: Diagnostic screen to aid in factory support
- User Programmable Target Density: Used for calculating compaction %
- User Changeable Battery: Easily change batteries in the field
Operational Specification
Mode
|
Single |
Reading time less than five (5) seconds. Stores Data |
|
Average |
Averages five (5) readings and stores data including date and time. Stores thousands of records |
|
Continuous |
Instantaneous density readings. |
|
Segregation |
Identifies variations in material density associated with segregation. Function |
Function
|
Density |
% Compaction |
|
Integrated Temperature Sensing |
Real time temperature display O° F to 350 °F (-17.7° C to 177.6° C) |
Calibration Mode
|
Normal |
Correlation offset to cores |
Measurement Specification
|
Sensing Area |
11 in. (27.9cm) dia. base allows optimum measurement on fine and coarse material types. |
|
Measurement Depth |
User selected and adjustable from 1 in. to 4 in. (2Smm to 1OOmm) |
|
Measurement Display |
Density, % Compaction, Surface Temperature, Mix Name & Project Name |
Mechanical Specification
|
Unit Weight |
6.44kg (14.2 lbs) |
|
Unit Dimensions |
27,9 cm x 27,9 cm x 30,4 cm (11"x11"x12" High) with handle extension 73,6 cm High (29") |
|
Shipping Weight |
w/ Case 19,27 kg (42,5 lbs) |
|
Shipping Dimensions |
63,5 cm x 50,8 cm x 35,5 cm (25" x 20" x 14") |
Electrical Specification
|
Microprocessor |
Controlled |
|
CE Mark |
Complies with EN 61000-4-2, 61000-4-3, 61000-4-8 |
|
Battery |
14.0 Amp-hr NiMH, 7.2 V |
|
Recharge Time |
4 hours |
|
Battery Charger |
Self Contained CE & UL Certified Universal AC Charger, DC Charger |
|
Computer Ports |
1 USB Port |
25. Hand Type Digital Thermometer
Product Code
|
UTGT-1350 |
Hand Type Digital Thermometer, -50° C to 1350° C |
|
UTGT-1370 |
200 mm Hand-Held Penetration Probe, for Tempereture Mesurement (Ø6mm), with 1.5m cable and connector, up to 1200° C, Type: OM07-K160-20 M 1K |
|
UTGT-1371 |
300 mm Hand-Held Penetration Probe, for Tempereture Mesurement (Ø6mm), with 1.5m cable and connector, up to 1200° C, Type: OM07-K160-30 M 1K |
|
UTGT-1372 |
500 mm Hand-Held Penetration Probe, for Tempereture Mesurement (Ø6mm), with 1.5m cable and connector, up to 1200° C, Type: OM07-K160-50 M 1K |
Digital thermometer and penetration probes are used together for measuring the delivery and compaction temperatures of bituminous mixtures. Preffered penetration probe should be ordered with UTGT- 1350.
|
Dimensions |
50x110x170 mm |
|
Weight (approx.) |
0,40 kg |